Bartın Üniversitesi
Kurumsal Akademik Arşivi
    • English
    • Türkçe
  • English 
    • English
    • Türkçe
  • Login
  • POLİTİKA
  • REHBER
  • İLETİŞİM
View Item 
  •   Bartın University Dspace
  • Enstitüler
  • Fen Bilimleri Enstitüsü
  • Orman Endüstri Mühendisliği Ana Bilim Dalı
  • Orman Endüstri Mühendisliği Ana Bİlim Dalı Yüksek Lisans
  • View Item
  •   Bartın University Dspace
  • Enstitüler
  • Fen Bilimleri Enstitüsü
  • Orman Endüstri Mühendisliği Ana Bilim Dalı
  • Orman Endüstri Mühendisliği Ana Bİlim Dalı Yüksek Lisans
  • View Item
JavaScript is disabled for your browser. Some features of this site may not work without it.

Tutkallamada yonga sıcaklığının levha özelliklerine etkisi

Thumbnail
View/Open
5-Özgür Yiğittap.pdf (1.474Mb)
Date
2016-12-12
Author
Yiğittap, Özgür
Metadata
Show full item record
Abstract
Bu çalışmada yonga sıcaklığındaki değişimin yonga levhaların mekanik ve fiziksel özelliklerine etkisi araştırılmıştır. Yonga levhaların üretiminde %30 iğne yapraklı, %35 yapraklı ağaç yongaları (gürgen, kayın) ve %35 kavak odun yongaları kullanılmıştır. Tek tabakalı levhaların üretiminde %10 üre formaldehit (UF) tutkalı kullanılmıştır. Üretilen deney levhalarının fiziksel ve mekanik özellikleri tespit edilmiştir. Elde edilen sonuçlara göre; levha üretimi için gerekli en uygun yonga sıcaklığının 30 ile 40 0C arasında olduğu tespit edilmiştir. Bu şartlarda ortalama eğilme direnci 15,14 N/mm2, yüzeye dik çekme direnci 0,75 N/mm2 ve vida tutma direncinin ise 1011 N olduğu saptanmıştır. Deney sonuçlarına göre 50°C ve 55°C yonga sıcaklığındaki levhaların ortalama çekme direnci değeri 0,57 N/mm² olarak tespit edilmiş olup bu sonuçların 30-40 0C üretilen levhalara göre % 19 daha düşük olduğu hesaplanmıştır. Bu durum tutkallamada yonga sıcaklıklarının yükselmesiyle direnç değerlerinin düştüğünü, bu yüzden aynı direnç değerlerini yakalamak için daha fazla tutkal kullanılması gerektiğini göstermektedir. Bu durum da tutkal sarfiyatının artmasına neden olacaktır. Buna karşın tutkallamada yonga sıcaklık değişiminin su alma ve eğilme direnci üzerine ise önemli bir etkisinin olmadığı görülmüştür.
 
In this study, the effect of chip temperature changes on the mechanical and physical properties of particle boards (PBs) was investigated. As raw materials were used 30% softwood, 35% hardwood (hornbeam, beech) and 35% poplar wood chips in particle board production. Urea formaldehyde (UF) resin was used as a binder in the production of singlelayer PBs in the ratios of 10%. Mechanical and physical properties of test boards were determined. As a result, it was determined that the optimum chip temperature for board production is between 30 and 40 0C. Under these conditions, average bending strength, internal bond strength and the screw withdrawal strength parallel to surface were determined 15.14 N /mm2, 0.75 N/mm2 and 1011 respectively. According to experimental results, average internal bond strength was determined 0,57 N/mm² in 50 and 550C of chip temperature. This value (0,57) is 19% lower than boards made from 30 and 400C of chip temperature. It was show that increasing chip temperature has led to a decrease of strength values in gluing. For this reason, more glue will be required to achieve the same resistance values and so glue consumption will increase. On the other hand, it was observed that the change of chip temperature did not significant effect on the water absorption and bending resistance in the gluing.
 
URI
http://hdl.handle.net/11772/256
Collections
  • Orman Endüstri Mühendisliği Ana Bİlim Dalı Yüksek Lisans [61]

DSpace@Bartın is member of:


sherpa/romeo
Dergi Adı / ISSN Yayıncı

Exact phrase only All keywords Any

Başlık İle Başlar İçerir ISSN


Browse

All of CommunitiesCommunities & CollectionsBy Issue DateAuthorsTitlesSubjectsTypesDepartmentsPublishersLanguagesRightsJournalsThis CollectionBy Issue DateAuthorsTitlesSubjectsTypesDepartmentsPublishersLanguagesRightsJournals

My Account

LoginRegister

DSpace@Bartın is member of:

İLETİŞİM BİLGİLERİ

Adres
Bartın Üniversitesi Kutlubey Yerleşkesi Kütüphane ve Dokümantasyon Daire Başkanlığı Merkez/BARTIN, 74100
E-Posta
acikerisim@bartin.edu.tr
Creative Commons License

DSpace@Bartin by Bartin University Institutional Repository is licensed under a Creative Commons Attribution-NonCommercial-NoDerivs 3.0 Unported License.